## GlyphEditor.catalog   Version 1.00   February 2002

Ucode GlyphEditor - by Ken Shillito
Load
Grab another glyph
Save
Grab from Font
Help
Grab from Picture
Can't load glyph file - out of memory
(Click the close window gadget)
##10
Caution: Unsaved glyph alterations
Quit
Cancel
Save was bad
(Click the close window gadget)
Unicode of glyph to copy from
OK
Cancel
Click vertical line to insert
Click vertical line to delete
##20
Click horizontal line to insert
Click horizontal line to delete
## start of TLGfiles
Click a file to load it...
Surrogate
Nominal Height
Width
Weight
Unicode
Style
0000
##30
00
Cancel
(No files match this surrogate, size)
Click a size to choose it
(The number of files of each size is
 shown after it in parenthesis)
(Click to acknowledge)
Click a surrogate to choose it
##end of TLGfiles
A font is already open - use it again?
Yes
##40
No
## string 41 must not contain &...; 
Choose a font...
ASCII value to grab (normally 21-7E or A1-FF)
Unicode value to jump to
Can’t grab font - out of memory
(Click the close window gadget)
Grab from picture....

Sorry - this feature is not yet implememented
(Click the close window gadget)
##50


 Ucode GlyphEditor - Help
 ~~~~~~~~~~~~~~~~~~~~~~~~
   When GlyphEditor starts up, it loads the glyph file

          U0B/NMSS100

   for editing, and shows glyph 0041.

##60
 The editing window has...
 ~~~~~~~~~~~~~~~~~~~~~~
   Three rows of buttons
   The Unicode and file of the glyph being edited
   A grid of pixels of the glyph being edited
   The glyph being edited, with those before and after
   
   To change the pixels of a glyph, use the
                left mouse button.
   Click an off pixel to switch it on.
##70
   Click an on pixel to switch it off.
   You can move the mouse around with the
                left button held down 
                to switch more pixels on or off.

 The Buttons....
 ~~~~~~~~~~~
   Load   To load another glyph file
   Save   To save the glyph file being edited
   Help   What you are viewing now
##80

   Grab another glyph    To copy a glyph from another
                         Unicode to this Unicode
   Grab from font        To grab a glyph from any
                         Amiga font
   Grab from picture     To grab a glyph from a
                         picture (not yet implemented)                         

   ⇦  Move glyph 1 pixel left
   ⇧  Move glyph 1 pixel up
##90
   ⇨  Move glyph 1 pixel right
   ⇩  Move glyph 1 pixel down
   ⇔  Mirror the glyph
   ⇕  Invert the glyph
   +V  stretch the glyph by 1 vertical line
   -V  shrink the glyph by 1 vertical line
   +H  stretch the glyph by 1 horizontal line
   -H  shrink the glyph by 1 horizontal line
   ✗  Clear the glyph
    <  back 1 Unicode
##100
    >  forward 1 unicode
   <4  back 4 unicodes
   >4  forward 4 unicodes
   <<  back 16 unicodes
   >>  forward 16 unicodes
   ↻  Undo       Undoes the last change to this unicode
                       (does not undo jumps to another unicode)
   ⎗  Restore    Undoes all changes made to this unicode
                        since it appeared on the grid.
    U  Go to a specified Unicode within the file being edited
##110

 Other keyboard features
 ~~~~~~~~~~~~~~~~~~~~~~~
   If you press the numbers 1 to 9, it will act a a multiplier
          if you immediately then press one of the keys
          ⇦ ⇧ ⇨ ⇩
          +V -V +H -H
          < > <4 >4 << >>

   The left or right arrow keys step to the the previous
##120
          or next unicode

 To quit
 ~~~~~~~
 Click the window’s close gadget, or press <Esc>

 Note
 ~~~~
   It is helpful to have Ucode’s GlyphViewer
   running at the same time as GlyphEditor, so you can see
##130
   what you are doing.

   If GlyphEditor saves a glyph file, GlyphViewer will
   need to re-load it to make the changes visible.