# header LOCALE_GALERTEST
;
; GALerTest.cd V1.41
;
; GALerTest 1.41 locale description file
;
; (c) 1991-93 by Christian Habermann
;
;
;**************************  menu text ****************************
;
; gadgets
MSG_END_GAD (0/1/)
   END   
;
MSG_CANCEL_GAD (/1/)
 Cancel
;
MSG_CONT_GAD (/1/)
Continue
;
MSG_ERR_TIMER (/1/)
can't get timer
;
MSG_ERR_INTLIB (/1/)
can't open intuition.library V37
;
MSG_ERR_FONT (/1/)
can't get topaz.font 8
;
MSG_ERR_GRAPHLIB (/1/)
can't open graphics.library V37
;
MSG_ERR_REQTOOLSLIB (/1/)
can't open reqtools.library V38
;
MSG_ERR_WIN (/1/)
can't open window
;
MSG_HARDWARE_TXT (/1/)
Which hardware-version of GALer do you want to test?\n\
(look at your circuit diagram for the version number)
;
MSG_INTRO_TXT (/1/)
This is a program for testing the hardware of the GALer project.\n\
You need this program to adjust the trimpots too.\n\
IMPORTANT: There must be no GAL in the Textool socket now!\n\n\
If the hardware works not as the test program demands, then\n\
you should cancel 'GALerTest' immediately and try to remove the\n\
bug in your hardware.\n\n\
Please select the 'Continue' gadget to start the test.
;
MSG_TEST1_TXT (/1/)
Now the LED should be off and all pins of the Textool socket should\n\
be set at LOW level (about 0 volt).\n\n\
Please select 'Continue'!
;
MSG_TEST2_TXT (/1/)
Now the LED should be on.\n\n\
Please select 'Continue'!
;
MSG_TEST3_TXT (/1/)
Now the LED should be off again.\n\n\
Please select 'Continue'!
;
MSG_TEST4_TXT (/1/)
At pin 24 of the Textool socket should be a HIGH level (about 5 volt).\n\n\
Please select 'Continue'!
;
MSG_TEST5_TXT (/1/)
At pin 22 of the Textool socket should be a HIGH level too.\n\n\
Please select 'Continue'!
;
MSG_TEST6_TXT (/1/)
At all pins should be a HIGH level with exception of pin 12.\n\
Pin 12 is GND.\n\n\
Please select 'Continue'!
;
MSG_TEST7_TXT (/1/)
At pins 1, 3, 5, 7, 9, 11, 14, 16, 18, 20, 22, 24 should be a HIGH level.\n\
All other pins should be LOW.\n\n\
Please select 'Continue'!
;
MSG_TEST8_TXT (/1/)
Now at pins 2, 4, 6, 8, 10, 13, 15, 17, 19, 21, 23 should be a HIGH level.\n\
All other pins should be LOW.\n\n\
Please select 'Continue'!
;
MSG_TEST9_TXT (/1/)
Now you have to adjust the trimpots R40-R44.\n\
If this does not work, check IC9, IC10, T3, T4.\n\n\
Use trimpot R40 to adjust the voltage at pin 2 to exactly 16.5V.\n\
Please select 'Continue'!\n\n
;
MSG_TEST10_TXT (/1/)
Use trimpot R41 to adjust the voltage at pin 2 to exactly 15.75V.\n\
Please select 'Continue'!\n\n
;
MSG_TEST11_TXT (/1/)
Use trimpot R42 to adjust the voltage at pin 2 to exactly 14.5V.\n\
Please select 'Continue'!\n\n
;
MSG_TEST12_TXT (/1/)
Use trimpot R43 to adjust the voltage at pin 2 to exactly 14.0V.\n\
Please select 'Continue'!\n\n
;
MSG_TEST13_TXT (/1/)
Use trimpot R44 to adjust the voltage at pin 2 to exactly 12.0V.\n\
Please select 'Continue'!\n\n
;
MSG_TEST14_TXT (/1/)
O.K., now all voltages are adjusted. Let me do some other tests.\n\
Please select 'Continue'!\n\
;
MSG_TEST15_TXT (/1/)
Now at pin 4 should be a voltage of 12.0V and pin 2 should be\n\
at LOW level. If this does not work, check T1, T2.\n\n\
Please select 'Continue'!
;
MSG_TEST16_TXT (/1/)
Now I'm trying to read pins 14-23 of the Textool socket...\n
;
MSG_TEST17_TXT (/1/)
 ERROR!!!\n\
   There must be an error at the BUSY line, R27, IC8, IC6, IC7\n\
   or R13. Please check this components.\n\n\
 Description of error:\n
;
MSG_TEST18_TXT (/1/)
  can't read pin 22 through the BUSY line of the parallel port
;
MSG_TEST19_TXT (/1/)
  can't read pins 14-21 through the BUSY line of the parallel port
;
MSG_TEST20_TXT (/1/)
  can't read pin 23 through the BUSY line of the parallel port
;
MSG_TEST21_TXT (/1/)
O.K., no error found (you have a lot going for you).\n\n\
If you have found no errors and if you have adjusted all voltages\n\
(12V, 14V, 14.5V, 15.75V and 16.5V), GALer works fine.\n\n\
Now you can read/program GALs by using the software called GALer.
;
MSG_TEST22_TXT (/1/)
Use trimpot R16 to adjust the voltage at pin 2 to exactly 16.5 V.\n\
If this does not work, check IC9, T3, T4.\n\n\
Please select 'Continue'!
;
MSG_TEST23_TXT (/1/)
Now at pin 4 should be a voltage of 16.5 V and pin 2 should be\n\
at LOW level. If this does not work, check T1, T2.\n\n\
Please select 'Continue'!
;
MSG_TEST24_TXT (/1/)
O.K., no error found (you have a lot going for you).\n\n\
If you found no errors and if you have adjusted the 16.5V,\n\
GALer works fine.\n\n\
Now you can read/program GALs by using the software called GALer.
;
MSG_TEST25_TXT (/1/)
Now I'm trying to read pins 14-22 of the Textool socket...\n