#ifndef DEVICES_SERIAL_H #define DEVICES_SERIAL_H 1 /* ** serial.h for ACE Basic ** ** Note: Translated to ACE by ConvertC2ACE ** @ MapMeadow Software, Nils Sjoholm ** ** ** Date: 09/03/95 ** ** */ /* ** This are the StructPointer defines for serial.h */ #ifndef IOExtSerPtr #define IOExtSerPtr ADDRESS #endif #ifndef IOTArrayPtr #define IOTArrayPtr ADDRESS #endif /* ** End of StructPointer defines for serial.h */ #ifndef EXEC_IO_H #include #endif /* EXEC_IO_H */ /* array of termination char's */ /* to use, see serial.doc setparams */ STRUCT IOTArray LONGINT TermArray0 LONGINT TermArray1 END STRUCT #define SER_DEFAULT_CTLCHAR &H11130000 /* default chars for xON, xOFF */ /* You may change these via SETPARAMS. At this time, parity is not calculated _for xON/xOFF characters. You must supply them with the desired parity. */ /******************************************************************/ /* CAUTION !! IF YOU ACCESS the serial.device, you MUST (!!!!) use an IOExtSer-sized structure or you may overlay innocent memory !! */ /******************************************************************/ STRUCT IOExtSer IOStdReq IOSer LONGINT io_CtlChar /* control char's (order = xON, xOFF, INQ, ACK) */ LONGINT io_RBufLen /* length in bytes of serial port's read buffer */ LONGINT io_ExtFlags /* additional serial flags (see bitdefs below) */ LONGINT io_Baud /* baud rate requested (true baud) */ LONGINT io_BrkTime /* duration of break signal in MICROseconds */ IOTArray io_TermArray /* termination character array */ BYTE io_ReadLen /* bits per read character (# of bits) */ BYTE io_WriteLen /* bits per write character (# of bits) */ BYTE io_StopBits /* stopbits for read (# of bits) */ BYTE io_SerFlags /* see SerFlags bit definitions below */ SHORTINT io_Status END STRUCT /* status of serial port, as follows: * BIT ACTIVE FUNCTION * 0 --- reserved * 1 --- reserved * 2 high Connected to parallel "select" on the A1000. * Connected to both the parallel "select" and * serial "ring indicator" pins on the A500 * & A2000. Take care when making cables. * 3 low Data Set Ready * 4 low Clear To Send * 5 low Carrier Detect * 6 low Ready To Send * 7 low Data Terminal Ready * 8 high read overrun * 9 high break sent * 10 high break received * 11 high transmit x-OFFed * 12 high receive x-OFFed * 13-15 reserved */ #define SDCMD_QUERY CMD_NONSTD /* $09 */ #define SDCMD_BREAK (CMD_NONSTD+1) /* $0A */ #define SDCMD_SETPARAMS (CMD_NONSTD+2) /* $0B */ #define SERB_XDISABLED 7 /* io_SerFlags xOn-xOff feature disabled bit */ #define SERF_XDISABLED (128) /* " xOn-xOff feature disabled mask */ #define SERB_EOFMODE 6 /* " EOF mode enabled bit */ #define SERF_EOFMODE (64) /* " EOF mode enabled mask */ #define SERB_SHARED 5 /* " non-exclusive access bit */ #define SERF_SHARED (32) /* " non-exclusive access mask */ #define SERB_RAD_BOOGIE 4 /* " high-speed mode active bit */ #define SERF_RAD_BOOGIE (16) /* " high-speed mode active mask */ #define SERB_QUEUEDBRK 3 /* " queue this Break ioRqst */ #define SERF_QUEUEDBRK (8) /* " queue this Break ioRqst */ #define SERB_7WIRE 2 /* " RS232 7-wire protocol */ #define SERF_7WIRE (4) /* " RS232 7-wire protocol */ #define SERB_PARTY_ODD 1 /* " parity feature enabled bit */ #define SERF_PARTY_ODD (2) /* " parity feature enabled mask */ #define SERB_PARTY_ON 0 /* " parity-enabled bit */ #define SERF_PARTY_ON (1) /* " parity-enabled mask */ /* These now refect the actual bit positions in the io_Status SHORTINT */ #define IO_STATB_XOFFREAD 12 /* io_Status receive currently xOFF'ed bit */ #define IO_STATF_XOFFREAD (4096) /* " receive currently xOFF'ed mask */ #define IO_STATB_XOFFWRITE 11 /* " transmit currently xOFF'ed bit */ #define IO_STATF_XOFFWRITE (2048) /* " transmit currently xOFF'ed mask */ #define IO_STATB_READBREAK 10 /* " break was latest input bit */ #define IO_STATF_READBREAK (1024) /* " break was latest input mask */ #define IO_STATB_WROTEBREAK 9 /* " break was latest output bit */ #define IO_STATF_WROTEBREAK (512) /* " break was latest output mask */ #define IO_STATB_OVERRUN 8 /* " status SHORTINT RBF overrun bit */ #define IO_STATF_OVERRUN (256) /* " status SHORTINT RBF overrun mask */ #define SEXTB_MSPON 1 /* io_ExtFlags. Use mark-space parity, */ /* instead of odd-even. */ #define SEXTF_MSPON (2) /* " mark-space parity mask */ #define SEXTB_MARK 0 /* " if mark-space, use mark */ #define SEXTF_MARK (1) /* " if mark-space, use mark mask */ #define SerErr_DevBusy 1 #define SerErr_BaudMismatch 2 /* baud rate not supported by hardware */ #define SerErr_BufErr 4 /* Failed to allocate new read buffer */ #define SerErr_InvParam 5 #define SerErr_LineErr 6 #define SerErr_ParityErr 9 #define SerErr_TimerErr 11 /*(See the serial/OpenDevice autodoc)*/ #define SerErr_BufOverflow 12 #define SerErr_NoDSR 13 #define SerErr_DetectedBreak 15 #ifdef DEVICES_SERIAL_H_OBSOLETE #define SerErr_InvBaud 3 /* unused */ #define SerErr_NotOpen 7 /* unused */ #define SerErr_PortReset 8 /* unused */ #define SerErr_InitErr 10 /* unused */ #define SerErr_NoCTS 14 /* unused */ /* These defines refer to the HIGH ORDER byte of io_Status. They have been replaced by the new, corrected ones above */ #define IOSTB_XOFFREAD 4 /* iost_hob receive currently xOFF'ed bit */ #define IOSTF_XOFFREAD (16) /* " receive currently xOFF'ed mask */ #define IOSTB_XOFFWRITE 3 /* " transmit currently xOFF'ed bit */ #define IOSTF_XOFFWRITE (8) /* " transmit currently xOFF'ed mask */ #define IOSTB_READBREAK 2 /* " break was latest input bit */ #define IOSTF_READBREAK (4) /* " break was latest input mask */ #define IOSTB_WROTEBREAK 1 /* " break was latest output bit */ #define IOSTF_WROTEBREAK (2) /* " break was latest output mask */ #define IOSTB_OVERRUN 0 /* " status SHORTINT RBF overrun bit */ #define IOSTF_OVERRUN (1) /* " status SHORTINT RBF overrun mask */ #define IOSERB_BUFRREAD 7 /* io_Flags from read buffer bit */ #define IOSERF_BUFRREAD (128) /* " from read buffer mask */ #define IOSERB_QUEUED 6 /* " rqst-queued bit */ #define IOSERF_QUEUED (64) /* " rqst-queued mask */ #define IOSERB_ABORT 5 /* " rqst-aborted bit */ #define IOSERF_ABORT (32) /* " rqst-aborted mask */ #define IOSERB_ACTIVE 4 /* " rqst-qued-or-current bit */ #define IOSERF_ACTIVE (16) /* " rqst-qued-or-current mask */ #endif #define SERIALNAME "serial.device" #endif /* DEVICES_SERIAL_H */