If you would like to receive e-mail updates of the software written for the PowerFlyer FastATA-2/EIDE Controller, please send a message to: support@elbox.com subject: subscribe FastATA'99 body: , , SOFTWARE INSTALLATION Note: Before you proceed with the installation of the software of the controller, uninstall any system add-on programmes like IDEFIX, EIDE device, etc. The following files are provided in the enclosed FastATA'99 floppy disk: ATA3.driver, ATA3-Install, ATA3Prefs, Mountlists: CD1, CD2, CD3, PC5, PC6, PC7, Orgella ReadMeFirst History.txt CheckLMB (Check Left Mouse Button) DriveSpeed ATAPIFormat FastATA'99.lha Copyright.doc Note: The controller without software installed operates only with the PRIMARY PORT, in exactly the same way as a standard A1200 controller. Note: Please remember that if you have only one drive attached to any port, jumpers on this drive should be set to SINGLE (MASTER). If you have two drives attached to any port, the first drive should have jumpers set to MASTER, the second to SLAVE. AUTOMATIC INSTALLATION 1. Boot the computer from the hard disk. 2. Run ATA3-Install from the FastATA'99 floppy disk. The installation shall proceed in a fully automatic mode. After installation of FastATA'99, reboot your Amiga with the left mouse button pressed during start: it will start ATA3Prefs program. Click SAVE on exit from ATA3Prefs. For installation/reinstallation of AllegroCDFS start ATA3-Install once again. ATA3-Install prepares all AllegroCDFS mountlists for your CD-ROM/CD-R/CD-RW/DVD drives. Note: The Installer program (from INSTALL Workbench) must be present in the SYS: folder of the booting disk. MANUAL INSTALLATION 1. Copy ATA3.driver and CheckLMB to the C: folder. 2. Copy ATA3Prefs to the Prefs: folder. 3. Add the following at the beginning of the startup-sequence: C:SetPatch QUIET C:CheckLMB IF WARN SYS:Prefs/ATA3Prefs ENDIF C:ATA3.driver QUIET Note: If you upgrade drivers, copy only new ATA3.driver and new ATA3Prefs to appropriate folders. 4. For manual installation of AllegroCDFS, copy AllegroCDFS to L: folder 5. Copy appropriate mountlists from FastATA'99:mountlists to Devs:DosDrivers HOW THE SOFTWARE WORKS The ata3.driver program recognises EIDE devices connected to the Amiga, detects the A1200 processor type and takes over all the calls to the scsi.device. The second run of the ATA3.driver gives only information on the devices connected and their modes of operation (PIO 0 to PIO 4). FastATA-2/EIDE Controller supports HDD > 4 GB by way of automatic HDD split into 4 GB logical units, which guarantees 100% compatibility with the Operating System and any previous software. If you connect hard disks of over 4 GB, they will be automatically divided into Units of the size below 4 GB. Split 4 GB units have Drive Revision 4Gxx in the HDToolBox program. In preferences in ATA3Prefs you can choose the mode of operation for either SPLIT (default) or TD64. The latter means that installing a HDD will NOT divide it into logical units. Then, use only the filesystems with TD64 or DirectSCSI commands implemented. Note: Run ATA3.driver before partitioning HDDs larger than 4 GB. Note: Some filesystems (e.g. FFS) don't support correctly partitions larger than 2 GB. See also FAQ in the end of ReadMeFirst. If any HDD partition is not validated, ATA3.driver will stop running until Amiga finishes validating this HDD. Note: PRIMARY PORT without ATA3.driver running works like standard Amiga IDE connector. ATAPI DEVICES If you have ATAPI-standard devices installed, the Devs/DOsDrivers folder has to include an appropriate mountlist. Note: You can make use of the CD0 mountlist included in the STORAGE disk of Workbench 3.1. The Unit parameter of the CD0 mountlist shall correspond to the Unit number for the given CD-ROM drive. PRIMARY MASTER Unit 0 PRIMARY SLAVE Unit 1 SECONDARY MASTER Unit 2 SECONDARY SLAVE Unit 3 Note: CDx mountlists for AllegroCDFS are stored in FastATA'99:mountlist folder Note: If you are using any other mountlist, always set the device=scsi.device for HDD, CD-ROM, CD-R, CD-RW drives and device=trackdisk.device for removable media like LS-120, ZIP-ATAPI. Removable media drives like LS-120, ZIP, etc., when formatted with the Amiga operational system, do not require any special mountlist as they are automatically recognised. When these media are used in the PC format, the Devs/DOsDrivers folder has to include an appropriate mountlist (PCx). Note: The Unit parameter of the PCx mountlist shall correspond to the drive Unit number (Unit = Unit number + 4). for PRIMARY MASTER use PC4 for PRIMARY SLAVE use PC5 for SECONDARY MASTER use PC6 for SECONDARY SLAVE use PC7 THE ATA3Prefs PROGRAM The ATA3Prefs will NOT operate when the ATA3.driver or any other software colliding with the ATA3.driver (e.g. IDEFIX, ASIM.device, etc.) has been started earlier. The ATA3Prefs may be used to manually adjust operation modes in any non-standard or old drives and to configure the ATA3.driver. Please start this program always after changing your hardware configuration. To store it, change exit by SAVE. It will save ATA3.Prefs configuration file in Envarc: folder. This file is used by ATA3.driver. Note: From ATA3.driver ver.3.6, in order to reach the full write speed on A1200 with 68040 it is necessary to start once ATA3Prefs and exit it with SAVE option. The ATA3.driver is a resident software as a rule, thus enabling auto-booting from LS-120 and ZIP disks. You can switch off this auto-booting option by changing ATA3Prefs settings. Any changes become valid after the computer is restarted. From the ATA3Prefs 3.0 on there is new, PIO4 NF mode added. Only the newest UDMA drives will work in this fastest mode. Note: Pressing the RESTORE button in the ATA3Prefs recalls the fastest settings and auto-booting after any unwanted changes made with the ATA3Prefs software. Note: With ATA3-Install script used, ATA3.driver and ATA3Prefs from the floppy disk are installed in such a way that keeping the left mouse button pressed at computer's boot-up causes ATA3Prefs to start. Otherwise, computer starts with ATA3.driver running. DRIVESPEED (works also without FastATA-2/EIDE controller) DriveSpeed is used for checking speed of any drives. Syntax: DriveSpeed scsi.device n where n is the unit number from 0 to 3. Note: For checking max CD-ROM speed, use CD-ROM disk larger than 675 MB. With smaller disks, only speed of the central (slower) sectors is read. ATAPIFormat ATAPIFormat is a low-level formatting program for any removable ATAPI media. Syntax: ATAPIFormat scsi.device n where n is the unit number from 0 to 3 FAQ I have a problem with disappearing data on my HDD 6.5 GB... ABOUT USING HDD > 4 GB The Scsi.device implemented in the A1200's ROM does not work properly with standard Amiga file systems when managing hard disks larger than 4 GB. Attempts to write to partitions above the 4 GB may result in damaging data located in lower partitions. New file systems, based on TD64 commands (TrackDisk.device 64) is an effort to cope with this situation. However, this solution does not assure full compatibility with the current software available for Amiga computers. Major malfunctions are observed in the working of software directly modifying disk sectors: the FORMAT system command, REORG, DPU, DiskSalve, QuarterbackTools and other programmes. (Using any of these in any partition above 4 GB may lead to damaging data in lower partitions.) PowerFlyer Fast-ATA2/EIDE controller solves all the problems related to the application of hard disks larger than 4 GB. The controller uses a method of managing large disks, which is different from TD64 commands. Disks larger than 4 GB are automatically splited into logical units of 4 GB size and a unit of a size, which is part of that amount, if needed. For example, a 18.3 GB disk will be divided into 4 disks of 4 GB each and a 2.3 GB disk. This method guarantees 100% compatibility of logical disks created in this way with all the software available for Amiga computers. Any file system (OFS, FFS, AFS, PFS-2, etc.) may be used, the disk may be partitioned with the standard HDToolBox, and partitions may be formatted with the FORMAT system command. Note: During partitioning disks larger than 4 GB, controller must be active. In order to do so, run the ATA3.driver before running HDToolBox (for partitioning HDD>4GB). If the disk to be installed is the only disk connected to the Amiga, the ATA3.driver must be run from the FastATA'99 floppy disk supplied with the controller. Below, please find the step-by-step instruction for installing a 4 GB hard disk in the Amiga with the PowerFlyer FastATA-2/EIDE controller, when the said disk is the only disk connected to the computer. (This disk shall be connected to the PRIMARY port as a MASTER disk.) INSTRUCTIONS 1. Turn on the computer and run WORKBENCH from the Install floppy disk. !!! From ATA3.driver ver. 4.0 !!! Start ATA3Prefs (from FastATA'99 floppy disk) and choice between SPLIT and TD64. Recommended option is SPLIT. Exit ATA3Prefs by SAVE. 2. Replace the floppy disk with the FastATA'99 floppy disk and run the ATA3.driver program. 3. Replace the floppy disk with the WORKBENCH Install floppy disk and run the HDToolBox. 4. The status line will have several logical disks with the status: UNKNOWN, Address = 0, Lun = 0, 1, ... 5. Mark the first of the logical disks and open the Change Drive Type options. 6. Select the Define New option. 7. Enter RAM: in the File Name field: before the file name (so as not to save to the Install floppy disk). 8. Select Read Configuration, then OK, then OK. 9. Start partitioning the first hard disk. (Please remember that FFS does not work properly with partitions larger than 2 GB; therefore, if you want some partitions to be present in the FFS, these should be smaller than 2 GB.) 10. After dividing the disk into partitions, select the Save Changes to Drive option. 11. Mark the next logical disk and proceed as in steps 5 to 10. Do the same for all logical disks. Note: Make sure that every partition is named differently. 12. EXIT from the HDToolBox. 13. Reset the computer with the Install floppy disk in its drive. 14. Stop the start of the computer with both mouse buttons pressed. 15. Then run the "Boot without startup-sequence." 16. Replace the floppy disk with the FastATA'99 floppy disk and run the df0:ata3.driver. 17. Return to the Install floppy disk and enter execute s:startup-sequence. 18. All the partitions will appear in the screen. Now quick format all the partitions... then everything should be clear. You can freely use a hard disk, which was prepared in this way, and writing to partitions above the 4 GB size will not lead to losing data in lower partitions. You could use any file systems: OFS, FFS, AFS, PFS-2 filesystems on any HDD partition. When you connect a 4 GB hard disk to Amiga with another hard disk fitted with the Workbench and installed FastATA-2/EIDE controller drivers, the installation procedure for > 4 GB hard disk is much simpler. Connect the installed disk as a PRIMARY SLAVE or to the second port. There is no need to swap floppies, and steps 14 to 17 are no longer necessary. If you would like to use TD64 command instead of splitting HDD > 4 GB start ATA3Prefs before ATA3.driver and set UP 4GB to TD64. SUPPORT If you have any questions about PowerFlyer FastATA-2/EIDE Controller, please contact with our technical supports: support@powerc.demon.co.uk or support@elbox.com