U S R O B O T I C S C O U R I E R ---------------------------------------------- H I G H S P E E D M O D E M S QUICK-REFERENCE CARD COURIER V.34 Fax COURIER Dual Standard V.34 Fax Internal and External Modems İ 1994 by U.S. Robotics, Inc 8100 North McCormick Blvd. Skokie, Illinois 60076-2999 All rights Reserved COURIER HIGH SPEED MODEMS BASIC COMMAND SET ----------------------------------------------------------------------------- Command Function/Options ----------------------------------------------------------------------------- $ Help Basic command summary. > (Greater Than) Repeat command continuously or up to 10 dial attemps. Cancel by pressing Any Key. +++ (Plus) Escape code sequence, preceded and followed by at least one second of no data. See DIP switch 9. / (Slash) Pause for 125 msec. A Force answer mode when modem hasn't received an incoming call. A/ Re-execute last command once. A> Repeat last command continuously. Any Key Terminate current connection attempt; exit Repeat mode. AT Attention. Must precede all commands except A/, A>, and +++. Bn Handshake options: B0 V.32/V.32 Bis mode; ITU-T answer sequence B1 HST mode; Bell answer tone D$ Help Dial command summary. Dn Dial the number that follows and go into Originate mode. Dial options: P Pulse dial T Tone dial , (Comma) Pause for 2 seconds ; (Semicolon) Return to command state after dialing " (Quotes) Dial the letters that follow ! (Exclamation point) Flash switch-hook to transfer call W Wait for a second dial tone (if X3 or higher set) @ Wait for an answer tone (if X3 or higher set) R Reverse frequencies DL Dial the last-dialed number. DSn Dial number stored in NVRAM at position n. En Command mode local echo. Not applicable after connection. See DIP switch 4. E0 Echo OFF E1 Echo ON Fn Local echo ON/OFF, once a connection is made. F0 Echo ON (Half Duplex) F1 Echo OFF (Full Duplex)--Default Hn On/Off hook control. H0 Hang up (go on hook) H1 Go off hook In Inquiry. I0 Product code I1 Memory (ROM) checksum I2 Memory (RAM) test I3 Call duration/real time I4 Current modem settings I5 NVRAM settings I6 Link diagnostics I7 Product configuration I10 Security account status I11 V.FC connection information Kn Modem clock K0 At 13 and 16, display current or last duration-- Default K1 At 13 and 16, display real time. Set clock with ATI3=HH:MM:SS K1 Ln Speaker volume (internal modems only) L0 Low L1 Low L2 Medium--Default L3 High Mn Monitor speaker. M0 Speaker always OFF M1 Speaker ON until carrier established--Default M2 Speaker always ON M3 Speaker ON after last digit dialed, OFF at carrier detect On Return online after command execution. O0 Return online, normal O1 Return online, retrain P Pulse dial. Qn Result codes display Q0 Display result codes Q1 Surpress result codes (Quiet mode) Q2 Quiet in answer mode only S$ Help S-Register summary. Sr=n Set register commands: r is any S-Register; n must be a decimal number from 0 to 255. Sr.b=n Set bit .b of Register r to n (0=OFF;1=ON). Sr? Query register r. T Tone dial. Vn Verbal/Numeric result codes. See DIP switch 2. V0 Numeric V1 Verbal Xn Result code options 0-7. See manual. Default is X7. Z Software reset. See DIP switch 10. AMPERSAND COMMAND SET ----------------------------------------------------------------------------- Command Function/Options ----------------------------------------------------------------------------- &$ Help Ampersand command summary &An ARQ result codes. &A0 Surpress ARQ result codes &A1 Display ARQ result codes &A2 Display HST and V.32 result codes &A3 Display protocol result codes--Default &Bn Serial port rate, computer-to-modem (DTE/DCE). &B0 Serial port rate follows connetion rate &B1 Fixed serial port rate--Default &B2 Fixed serial port rate in ARQ mode; variable rate in non-ARQ mode &Cn Carrier Detect (CD) See DIP switch 6. &C0 CD override &C1 Normal CD operations &Dn Data Terminal Ready (DTR). See DIP switch 1. &D0 DTR override &D1 Online command mode with DTR toggle &D2 Normal DTR operations &Fn Load a ROM template into RAM. See DIP switch 10. &F0 No flow control template settings &F1 Hardware flow control template settings &F2 Software flow control template settings &F3 HST Cellular template settings &Gn Guard tone. &G0 No guard tone (U.S., Canada)--Default &G1 Guard tone (Some European countries) &G2 Guard tone (United Kingdom; requires B0 &Hn Transmit Data flow control. &H0 Disable flow control &H1 Hardware (CTS) flow control--Default &H2 Software flow control (XON/XOFF) &H3 Hardware and Software control &In Received Data software flow control. &I0 Disable flow control--Default &I1 XON/XOFF to local modem and remote computer &I2 XON/XOFF to local modem only, ARQ mode only &I3 Host mode--Hewlet Packard protocol &I4 Terminal mode--Hewlet Packard protocol &I5 ARQ mode--same as &I2; non-ARQ mode--look for incoming XON/XOFF &Kn Data compression. &K0 Disable &K1 Auto enable/disable--Default &K2 Enable &K3 V.42 bis only &Ln Normal/Leased line. &L0 Normal phoneline--Default &L1 Leased line &L2 Enable HST Cellular &Mn Error Control/Synchronous options. &M0 Normal mode; no error control &M1 V.25 bis online synchronous with error control &M2-3 Reserved &M4 Normal/ARQ mode--Normal if ARQ connection cannot be made--Default &M6 V.25 bis synchronous mode with BISYNC &M7 V.25 bis synchronous with HDLC &Nn Link rate (DCE/DCE) &N0 Normal link operations--Default &N1 300 bps &N8 14.4K bps &N2 1200 bps &N9 16.8K bps &N3 2400 bps &N10 19.2K bps &N4 4800 bps &N11 21.6K bps &N5 7200 bps &N12 24K bps &N6 9600 bps &N13 26.4K bps &N7 12K bps &N14 28.8K bps &Pn Pulse dial make/break ratio. &P0 North America--Default &P1 United Kingdom and some Commonwealths &Rn Received Data hardware (RTS) flow control. &R0 Delay before CTS after RTS; see S26 &R1 Ignore RTS &R2 Pass receoved data on RTS high; used only if terminal equipment supports RTS--Default &Sn Data Set Ready (DSR) override. &S0 DSR override (always ON)--Default &S1 Modem controls DSR &S2 Pulsed DSR; CTS follows CD &S3 Pulsed DSR &S4 Modem sends DSR and CD together &Tn Modem testing. &Y0 End test, see Register S18 &T1 Analog Loopback (AL) &T2 Reserved &T3 Local Digital Loopback (LDL) &T4 Grant Remote Digital Loopback (RDL &T5 Deny RDL &T6 Initiate RDL &T7 RDL with selftest &T8 AL with self test &Wn Write current settings to NVRAM. &Yn Break handling. Destructive breaks clear the buffer; expedited breaks are sent immediately to the remote system. &Y0 Destructive, but don't send break &Y1 Destructive, expedited--Default &Y2 Nondestructive, expedited &Y3 Nondestructive, nonexpedited &ZC=s Write command string (s) to NVRAM. &ZC? Display stored command string. &Zn=L Store last-dialed number at position n. &Zn? Display phone number stored in NVRAM at position n, where n=0-9. PERCENT COMMAND SET ----------------------------------------------------------------------------- Command Function/Options ----------------------------------------------------------------------------- %$ Help percent command summary. %An Create and configure security accounts. See manual. %Bn Set local serial port rate from remote computer. %B0 110 bps %B6 9600K bps %B1 300 bps %B7 19.2K bps %B2 600 bps %B8 38.4K bps %B3 1200 bps %B9 57.6K bps %B4 2400 bps %B10 115.2K bps %B5 7200 bps %Cn Set local configuration from remote computer. %C0 Defer configuration--Default %C1 Restore original configuration %C2 Execute configuration %E=n Make security system edits. See manual. %Fn Set local data format from remote computer. %F0 No parity, 8 data bits %F1 Mark parity, 7 data bits %F2 Odd parity, 7 data bits %F3 Even parity, 7 data bits %L= Assign an account password as the local access password. See manual. %Nn Set Synchronous clock speed. See manual. %Pn=s Set the following remote access password string(s) at position n, where n=0 or 1. %Pn? Display the remote access password stored at position n, where n=0 or 1. %T Enable tone recognition. ----------------------------------------------------------------------------- DIP Factory Switch Setting Function ----------------------------------------------------------------------------- 1 UP Data Terminal Ready (DTR) Operations UP DTR normal; required for modem to accept commands DOWN DTR always ON (override) 2 UP Verbal/Numeric Result Codes UP Verbal (word) messages DOWN Numeric messages 3 DOWN Result Code Display UP Quiet mode; no display DOWN Display result codes 4 UP Command Mode Local Echo UP Modem echoes (displays) commands DOWN Modem does not echo 5 DOWN Auto Answer UP Modem answers on first ring DOWN Auto Answer suppressed 6 UP Carrier Detect (CD) Operations UP Indicates the modem is online and carrier signal is present DOWN CD signal always ON (override) 7 UP Auxiliary Switch, DIP Switch 3 DOWN UP Display result codes in Originate and Answer modes DOWN Suppress result codes in Answer mode 8 DOWN AT Command Set Recognition UP Disable AT command set recognition DOWN Normal operations 9 UP Escape Code (+++) Response UP Modem disconnects, returns to Command mode, returns NO CARRIER result DOWN Modem stays online, returns to Command mode, returns OK result 10 UP Power-On-Software Defaults UP Load from NVRAM (initially &F1 template) DOWN Load &F0 template S-REGISTER SUMMARY ----------------------------------------------------------------------------- Register Function Default ----------------------------------------------------------------------------- S0 Set number of rings before auto answer when See DIP DIP Switch 5 is UP. Default is 1. S0=0 suppresses switch 5 Auto answer, equivalent to DIP switch 5 DOWN S1 Counts and stores number of rings from an incoming call. 0 S2 Define escape code character. Default is +. 43 S3 Define ASCII Carriage Return. 13 S4 Define ASCII Line Feed. 10 S5 Define ASCII Backspace. 8 S6 Set number of seconds modem waits before dialing. 2 S7 Set number of seconds modem waits for a carrier 60 S8 Set duration, in seconds, of Pause (,) dial command 2 option and pause between command re-executions for Repeat (>) command. S9 Set duration, in tenths of a second, of remote carrier 6 signal before recognition. S10 Set duration, in tenths of a second, modem waits after 7 loss of carrierbefore hanging up. S11 Set duration and spacing, in miliseconds, of dialed tones. 70 S12 Define guard time, in 50ths of a second, for escape code 50 sequence. S13 Bit-mapped register: 0 1 Reset when DTR drops 2 Auto Answer in Originate mode 4 Disable result code pause 8 DS0 on DTR low-to-high 16 DS0 on power up or ATZ 32 Disable HST modulation 64 Disable MNP Level 3 128 Watchdog hardware reset S15 Bit-mapped register: 0 1 Disable high-frequency equalization 2 Disable online fallback 4 Force 300 bps back channel 8 Set non-ARQ Transmit buffer to 128 bytes 16 Disable MNP Level 4 32 Set Del as Backspace key 64 Unusual MNP incompatibility 128 Custom applications only S16 Bit-mapped register: 0 1 Analog Loopback 2 Dial Test 4 Test Pattern 8 Initiate Remote Digital Loopback 16-128 Reserved S18 &Tn test timer, disabled when set to 0. 0 S19 Set inactivity timer, in minutes, disabled when set to 0 0 S21 Length of break in ARQ mode, DCE to DTE, in ten- 10 millisecond units. S22 Define ASCII XON. 17 S23 Define ASCII XOFF. 19 S24 Set duration, in 20-millisecond units, of pulsed DSR 150 when modem is set to &S2 or &S3. S25 Set duration, in 100ths of a second, that DTR must be 1 dropped for the modem to respond. S26 Set duration, in 10 millisecond units, of delay between 5 RTS and CTS. S27 Bit-mapped register: 0 1 Enable V.21 modulation (300 bps) 2 Enable unencoded V.32 modulation 4 Disable V.32 modulation 8 Disable 2100 Hz answer tone 16 Disable MNP handshake 32 Disable V.42 Detect phase 64 Reserved 128 Unusual software incompatibility S28 Set duration, in tenths of a second, of the extra 3000/ 8 600 Hz answer tones sent during a v.32 handshaking. S29 Set duration, in tenths of a second, of V.21 hand- 20 shake delay. S32 Voice/Data switch function. Not a bit-mapped register. 9 See manual. S33 Enable reduced packet size. See manual. 0 S34 Bit-mapped register: 0 1 Disable V.32 bis 2 Disable Enhanced V.32 bis 4 Disable Quick V.32 Retrain 8 Enable V.23 modulation 16 Change MR LED to DSR 32 Enable MI/MIC 64 Disable remote access message 128 Disable V.32 terbo S38 Set duration, in seconds, before disconnect when 0 DTR drops during an ARQ call. S41 Set number of allowable login attempts for remote access. 0 S42 Define ASCII remote access escape character. 126 Default is -. S43 Define guard time, in 50ths of a second, for remote 200 access sequence. S44 Set duration, in seconds, of delay after modem senses 15 loss of carrier, before attempting to re-establish a leased-line connection. S51 Bit-mapped register: 0 1 Link Security enabled 2 Prompting enabled 4 Local access password protection enabled S54 Symbol rate bit-mapped register for debugging. Bit 6 0 (ATS54.6=1) disables Call Indicate (CI). Bit 7 (ATS54.7=1) disables V.8. S55 Trellis code bit-mapped register for debugging. 0 S56 Bit-mapped register for debugging. Bit 6 (ATS56.6=1) 0 disables V.34. Bit 7 (ATS56.7=1) disables V.FC. S57 Reserved for German operations. 0 ----------------------------------------------------------------------------- COM PORT AND IRQ JUMPER SETTINGS (INTERNALS) ----------------------------------------------------------------------------- ___ ___ IRQ2 |. .| |. .| COM1 (3F8Hex) |___| |___| .=====. .=====. IRQ3 ||. .|| ||. .|| COM2 (2F8Hex) || || || || `=====' `=====' ___ ___ IRQ4 |. .| |. .| COM3 (3E8Hex) |___| |___| ___ ___ IRQ5 |. .| |. .| COM4 (2E8Hex) |___| |___| ___ IRQ7 |. .| |___| ----------------------------------------------------------------------------- RS-232C INTERFACE PIN DEFINITIONS (EXTERNALS) ----------------------------------------------------------------------------- Signal Flow DB-25 DB-9 Circuit Function Computer to Modem ----------------------------------------------------------------------------- 1 - AA Chassis Ground both directions 2 3 BA Transmitted Data to modem 3 2 BB Recieved data to computer 4 7 CA Request to send to modem 5 8 CB Clear to Send to computer 6 6 CC Data Set Ready to computer 7 5 AB Signal Ground both directions 8 1 CF Carrier Detect to computer 12 - SCF Speed Indicate to computer 15 - DB Synchronous TX* Timing to computer 17 - DD Synchronous RX* Timing to computer 20 4 CD Data Treminal Ready to modem 22 9 CE Ring Indicate to computer 24 - DA Synchronous TX* Timing to modem * Indicates Transmitter (TX) or Receiver (RX) ----------------------------------------------------------------------------- Typed in by Puke/Mrb^Gms @BEGIN_FILE_ID.DIZ-------------------------------------------- _ _ __ __ |__ . __| morbid angels'95 ( Y )(__)( '!__)|(__! __ __ __ __ | __ .--|| )`--||--'|`--. presented to you: ŻŻ ŻŻŻ ŻŻŻ ŻŻŻ -------------------------------------------- USR COURIER QUICK REFERENCE CARD -------------------------------------[pK!]-- @END_FILE_ID.DIZ