Ref: 99960052 Title: ESD Rel.Note:SW/100-TCP-NCS/AT Ver.3.0 Part#86-0109-00 Rev.03 date: 03-27-89 Copyright 3Com Corporation, 1991. All rights reserved. 3Com Corporation Page 1 Software Release SW/100-TCP-NCS/AT Version 3.0 March 27, 1989 Part Number: 86-0109-00 Revision 03 TO: CS/100 Users FROM: 3Com Corporation SUBJECT: SW/100-TCP-NCS/AT Version 3.0 DATE: March 27, 1989 Enclosed is a distribution diskette containing SW/100-TCP-NCS/AT Version 3.0 (Part Number: 83-0048-02). This software runs on a CS/100 that is equipped with 512 kilo bytes of RAM and is booted from an NCS/AT. This release memo describes the procedure for installing the software on the NCS/AT, the new features, bugs fixed, limitations, and known problems in this version of SW/100-TCPNCS/AT. ** NOTE ** 3Com changed its software version numbering scheme in early 1989. Instead of using a five-digit number, such as 20060, 3Com now uses two- or three-digit numbers, such as 2.2 and 2.21. Higher version numbers represent more recent releases. For example, 2.21 is more recent than 2.2, 2.2 is more recent than 20060, and 20060 is more recent than 20000. Compatibility SW/100-TCP-NCS/AT Version 3.0 operates with the following products and software re leases: CS/1 running SW/1-TCP Version 20000 or later CS/1 running SW/20-TCP Version 3.0 or later CS/50 running SW/50-TCP Version 3.0 or later IB/3 running SW/20-IB Version 11000 or later NCS/2 running SW/2-NCS Version 2.0 or later NCS/AT running SW/AT-NCS Version 2.0 or later CS/200 running SW/200-TCP Version 20000 or later CS/210 running SW/200-TCP-CS/210 Version 3.0 or later Personal computer running SW/1-PCS Version 20000 or later. Table 1 illustrates the hardware and firmware compatibility requirements of SW/100-TCP-NCS/AT Version 3.0: Table 1 Hardware/Firmware Compatibility Product Boards PROMS CS/100 SIO T0ASYN 1B or later CS/100 MP T1MMON 2A or later ** NOTE ** You must press the Return key after you type each command described in this release memo. Refer to Chapter 3 of the TCP/IP Connection Service User's Guide for an explanation of the notation used in commands referenced in this release memo. Installation If you wish to make a backup copy of SW/100TCP-NCS/AT Version 3.0, use the floppy copy utility on the NCS/AT. Also, you must use a blank, 96-TPI, double-sided, high-density diskette to make the copy. Before your CS/100 can run SW/100-TCP-NCS/AT Version 3.0, you must install the software on the NCS/AT that boots the CS/100. Follow these steps to copy SW/100-TCP-NCS/AT Version 3.0 from the distribution diskette to the NCS/AT disk: 1. Follow the instructions in the NCS/AT Installation Guide to log in to the NCS/AT. A command prompt appears on the screen after you log in. 2. Before you load the new image, save the earlier version of SW/100- TCP-NCS/AT by typing: mv /BIN/cs100t /BIN/cs100t.xxxxx In this example, "xxxxx" is the version number of an earlier version of SW/100- TCP-NCS/AT. 3. Insert the SW/100-TCP-NCS/AT Version 3.0 diskette in the disk drive of the NCS/AT. 4. At the command prompt, type the following command to list the files contained on the diskette containing SW/100-TCPNCS/AT: utility floppylist The list displayed should contain the following files: /usr/NCS/BIN/cs100t.3.0 - image /usr/NCS/BIN/cs100l- loader /usr/NCS/bin/sgn/syncs100t12 - sysgen /usr/ncs/local/cmac_install /usr/ncs/local/cmac_uninstall /usr/ncs/local/cmac_src_unpak /usr/ncs/local/cmac_mk_install The last four files on the above list are conditional macros. 5. At the command prompt, type the following command: utility floppyread 6. The floppyread utility copies the software from the SW/100-TCP- NCS/AT diskette to the NCS/AT disk. As the files are copied to the disk, their names are displayed. If floppy read errors or disk write errors occur, remove and replace the diskette; then repeat the procedure starting at step 3. If read or write errors continue to occur, or if other error messages appear, contact your network supplier or 3Com for help. 7. After the files have been successfully copied, the command prompt appears. Remove the distribution diskette from the disk drive. Binding Your CS/100 to the NCS/AT Your CS/100 must be bound to the NCS/AT before it can boot from the NCS/AT. Follow these steps to bind your CS/100 to the NCS/AT, using the new loaderfile option on the NCS/AT. If your server is already bound to the NCS/AT, start at step 1. Otherwise, continue on to step 3. 1. Enter the UNBind command on the NCS/AT by typing: unb
where address is the Internet address of your server. This command removes your CS/100 from the list of servers bound to the NCS/AT. The system prompts you to indicate whether you wish to remove the client server's global parameter, Internet address, and configuration files from the NCS/AT disk. 2. Type "n" to save your configurations. 3. Enter the BInd command on the NCS/AT by typing: bi -f cs100t.3.0 -l cs100l [] This binds the CS/100 to the NCS/AT. In the above command line, "l" refers to the new loaderfile option and cs100l is the loaderfile name. If you do not specify the last argument, nports, the NCS/AT creates port configurations for the maximum number of ports on your Communications Server. New Features The following features, which were not available in SW/100-TCP-NCS/AT Version 20000, have been implemented in SW/100-TCP-NCS/AT Version 3.0: Access control is available on all Communications Servers that are booted from local diskettes, NCS/2s, or NCS/ATs. It is not available on a Communications Server that is booted from an NCS/150. Access control services are provided on the NCS, and supported by your Communications Server. Access control is disabled by default but it can be enabled from the Sysgen program on your NCS/AT. The Sysgen program now includes Access Control Parameters and Remote Access Parameters to support access control on your CS/100. Refer to the section Sysgen Changes in this release memos for information on these parameters. Enabling access control restricts access to the resources on your network and prevents unauthorized access to the network and network resources. The network manager maintains the access control database on the NCS. Refer to the NCS/AT Operation Guide for information on maintaining the database and on the new utilities that have been provided on the NCS for this purpose. In addition, the following access control parameters and commands have been implemented at local network manager privilege level in SW/100- TCP-NCS/AT Version 3.0: The DefaultLoginName parameter specifies the default user login name assigned to a host port to which secure connections are made. This default user name should be defined along with other users in the access control database on the NCS. Before you can set the DefaultLoginName parameter, you must set the TermPortDe- Login parameter in Sysgen. The SECurityServerAddress parameter specifies the Internet address of the NCS, which provides user authentication during login and network access control services. If no address is assigned, the address of the server's File Server is used. The SHow InternetServers command also shows the address of the Security Server on servers that use access control. The SHow LOgins command shows the name of the user logged in to each port on a Communications Server. The user name is displayed whether the login is done by a user or by automatic default login. The access control service is transparent to network users except for the following steps: - A user enters a user name and password before attempting to establish a connection to a resource. The user name is entered at the "Network Login:" prompt, which appears on the screen when the terminal is first powered on, and the password at the "Password:" prompt. The PassWord command allows a user to change his password. - A user enters the LOgout command when disconnecting from the network. This command disconnects all sessions and prevents unauthorized access to resources on the network. If a user tries to connect to a resource to which he does not have authorized access, the following error message is displayed: Access to resource denied A new parameter, # of keep alive packets, has been added to the TCP Parameters Menu in Sysgen. This parameter determines the number of packets transmitted to maintain a connection before it is terminated. The possible values of this parameter are from 0 through 10 (hexadecimal) and the default value is 0. For example, if this parameter is set to 8, the connection is terminated after eight keep alive packets have been sent. When this parameter is set to 0, the connection is maintained indefinitely. Keep alive packets are sent at intervals of from 45 to 60 seconds. Another new parameter, maximum window size, has been added to the TCP Parameters Menu in Sysgen. The maximum window size parameter enables you to change the window size for transmission and reception. The default window size is 1,024 bytes. This parameter can be set to hexadecimal values from 1 to 1000. A new set of audit trail messages has been implemented for Communications Servers that use access control. The audit trail record codes, IX for ICMP transmitted and IR for ICMP received, now display more information to aid in network fault analysis. Refer to the NCS/AT Operation Guide for a description of the revised audit trail messages and record codes. Additional features have been provided to support Hewlett Packard devices. These include default parameter settings, context-sensitive flow control, and spare XON forwarding. The SHow SESsion command has a new option, M. This option displays the Internet address and the TCP port number on the destination side of a connection. The new syntax for the SHow SESsion command is as follows: SHow (!) SESsion M For example, if you enter this command: sh (!1) ses m the screen display generated is similar to the following: CONCTD from 192.9.205.071:099:006 This display shows that the host server is connected from port 6 of a Communications Server with the address of 192.9.205.071. The number immediately following the Internet address ("099" in this example) may be disregarded. This feature only works if the destination server is a Communications Server manufactured by 3Com. In accordance with the latest updates in the TCP/IP implementation of the Berkeley release 4.3 of the UNIX operating system, this version has implemented retransmission and round-trip algorithms, delayed acknowledgements, superior silly-window avoidance behavior, and improved timer handling and disconnection procedures. The effects of these implementations include higher data throughput and more reliable connections. When entering commands in remote mode, the response timeout period has been increased from 12 to 28 seconds. This is particularly useful for Communications Servers that are booted from an NCS/2, which often requires a response time of more than 12 seconds. The LongBReakAction parameter is now available for both host and terminal ports. Previously this parameter could not be set for host ports. For more information on this parameter, refer to the TCP/IP Connection Service User's Guide. Sysgen Changes Two new options have been added to the Sysgen program to support access control on your CS/100. Invoke the sysgen utility on the NCS/2 by typing the following command: sysgen cs100t.3.0 The main sysgen menu is displayed. The new options, Access Control Parameters and Remote Access Parameters, have been added to the Module Select Menu in the Sysgen program. The following is the new mod ule select menu: Module Select Menu 1. Kernel Parameters 2. Data Link Parameters 3. IP Parameters 4. TCP Parameters 5. User Interface Parameters 6. Virtual Terminal Parameters 7. Statistics Monitoring Parameters 8. Service Listener Port List 9. Access Control Parameters A. Remote Access Parameters (ESC to return to main menu) Select module: Access Control Parameters Select 9 from the Module Select Menu to display the Access Control Parameters menu. The following menu is displayed: Access Control Parameters Parameter Current Value 1. Acs Ctl Enable(0=Dis, 1=Ena) 0x0 (ESC to return to previous menu) Enter selection: Type "1" at the "Enter Selection:" prompt to enable access control. Enabling access control restricts access to the resources on your network and prevents unauthorized access to the network and network resources. Access control is disabled by default. Remote Access Parameters The remote access parameters allow you to restrict the addresses of devices that can access your Communications Server with the REMOTE command. You can allow all devices, a group of devices, or individual devices to have remote access. Select A from the Module Select Menu to display the Remote Access Parameters Menu: Remote Access Parameters 1. Access Level (Any device) 2. Enter Device Addr here (ESC to return to previous menu) Enter selection: The possible values of the Access Level parameter are as follows: the address list consists of individual device addresses defined by the Enter Device Addr here option on the Remote Access Parameters menu. any device address list only address list plus subnetwork address list plus network Select item 1 from the Remote Access parameters to set this parameter. The screen prompts as follows: (ESC to return to previous menu) Enter selection: Choose 0(any), 1(address list), 2(also subnet) or 3(also network): - Select 0 to grant access to all devices on the network. This is the default value. - Select 1 to allow only those hosts listed in the address list to access the Communications Server. - Select 2 to allow all devices specified in the address list as well as all devices on the local subnetwork to access the Communications Server. - Select 3 to allow all devices specified in the address list and all devices on the local network to access the Communications Server. Select item 2, Enter Device Addr here, to define the addresses in the address list. The system displays the following: Enter an IP address: If you enter a valid Internet address, the new address and the value of the access level parameter appear on the screen and you are prompted to add the next address. For example, if you enter the valid Internet address 192.9.200.34, the following is displayed: Remote Access Parameters 1. Access Level Address List 2. Device IP addr 1 192.9.200.34 3. Enter Device Addr here (ESC to return to previous menu) Enter selection: You can specify up to three addresses on the address list. The system automatically numbers and lists the device addresses as you enter them. For example, if you define three addresses, the screen display will be similar to the following: 1. Access Level Specified Addresses 2. Device IP addr 1 192.9.200.45 3. Device IP addr 2 192.9.201.33 4. Device IP addr 3 192.9.201.22 The address list consists of the three addresses listed above. To delete a device address from the address field, select option 2, 3, or 4 and then enter 0.0.0.0 or x in the address field. If you wish to prevent all devices from accessing the Communications Server with the REMOTE command, set the Access Level Parameter to Address List, and check that there are no entries in the address list. Bugs Fixed Certain problems, which existed in previous versions of SW/100-TCP- NCS/AT, have been solved in SW/100-TCPNCS/AT Version 3.0. These problems and their resolutions are described below. If you attempt to save default port parameters in a non-numbered file and you do not have global network manager privilege level, the system now displays the error message "Insufficient privilege" after you enter the SAve command. Previously, this message or the system prompt was not displayed until you pressed the Break key. Only a global network manager can save default port parameters in a non-numbered file. The Domain name resolver no longer attempts to search infinitely for a canonical name when two canonical names that are aliases for each other have been defined by error in the Domain name server database, and you specify one of these names with the Connect or SHow NAme command. Previously, you had to reboot the server to terminate this infinite loop. Previously, if you entered the command, SH NAmes or SH NAmes *, the Domain name server failed to respond and the system crashed after the timeout period had expired. These commands are no longer valid so you must specify a name. If you attempt to issue these commands without specifying a name, the following error message appears: can only show unique Domain names You can now establish interconnections properly. Previously, when certain interconnections were requested, the system crashed. You can now specify the local broadcast address when you enter the global network manager form of the Broadcast command without disrupting the network. Previously, this command caused extremely heavy traffic on the network. The SHow LinePRotocol command now displays correct information. Previously, it always showed the value of the LinePRotocol parameter as BYTEsynchronous. Also, you can no longer change the value of this parameter with the SETD command. You can now simultaneously run three or more recursive macros that contain Connect or DisConnect commands. Previously, the system crashed within three hours of invoking the macros. Setting the NetAscii parameter of a port to UseNul no longer causes spurious ^A characters to be inserted in the data stream sent to that port. The CS/100 now consistently passes special characters, for example, , as data. Previously, it often failed to do this in incoming connections, and processed them instead. When the DataForward parameter is set as the result of an echo negotiation by a destination server using the Telnet protocol, it no longer automatically changes to None after the echo has been negotiated. An error, which caused the Domain name resolver to fail to respond to inquiries under certain circumstances, has been corrected. This version attempts to establish connections to permanent circuits (PVCs) according to the order in which the connection requests are received. Previously, priority was always given to the attempt to connect to the lowest numbered PVC. Also, you can successfully establish more than one PVC. Previously, you could not reliably do this. Domain name requests are sent to the NCS address specified by the FileServer- Address parameter if both the PrimaryNS and SecondaryNS parameters are not defined. Previously, no alternate address was available to respond to these requests. Network errors are now recorded in the audit trail record with the code "NE." Previously, they were coded as "EE." The boot time displayed by the SHow VERsion command now displays the actual boot time. Previously, the time was computed. Previously, you could not perform certain file transfer tasks if, after establishing a connection, you disabled the ECM character with the following command: SET ECMchar = disabled For example, if you attempted to transfer files from a personal computer, setting this parameter sometimes caused data loss. This resulted in failure of the file transfer. This problem has been fixed. The session number field in the audit trail messages coded CD and DC has been replaced by a four-digit field which indicates the TCP protocol port number. Previously the session number field always displayed 0, regardless of the session number. You can no longer assign an Internet address beginning with 127 to a Communications Server or a port. This number is reserved for loopback according to the TCP/IP protocol implementation. If you attempt to assign an Internet address beginning with 127, the following error message is displayed: Address cannot be broadcast at loopback. You must reassign existing Internet addresses that begin with 127. When two Communications Servers on the network have the same Internet address, you can now issue commands from a source server that specify the source server as the destination. Previously, for example, if ServerA and ServerB had the same Internet address and you issued the PIng command from ServerA, ServerB's host was pinged instead of ServerA's. A problem with the Domain name resolver, which arose on Communications Servers on which the maximum number of sessions was being held, has been corrected. Previously, for example, if you entered the Name or Connect command on a CS/100 on which the maximum number of sessions for that server was being held, the Domain name resolver did not respond and the following error message was displayed: No memory resource Even if the number of sessions was reduced, the Domain name resolver still did not function. When forwarding data, the Telnet code now removes the ASCII control character NUL when it follows the control character CR. Previously, it failed to do this, which caused data forwarding problems when Telnet is used in conjunction with the Berk eley 4.3 release of the UNIX operating system. Previously, the CS/100 crashed when it received a large number of ARP broadcast packets sent over the UNIX Operating System. This has been fixed. The system no longer crashes if you perform the following sequence steps: - Enter the Connect command - Enter the ECM character - Set the BReakAction parameter to IGnore and the BReakChar to ^C - RESume the session - Hold down the Control key and the "C" key simultaneously Limitations Version 3.0 has the following limitations: Automatic user default logins cannot be performed on terminal ports of a CS/100 running SW/100-TCP Version 3.0. You can change the virtual port configuration with the SETDefault command only on the first virtual port on your Communications Server. If you attempt to change other virtual port configurations with this command, the following error message is displayed: Portid out of range Also, if you change the configurations for the first virtual port, you must enter the ReaD command before the changes can take effect. These changes take effect on all virtual ports. A CS/100 that uses access control normally performs a default login on a host port. However, if you add a host port to a rotary, you must use the Listen command on the rotary for it to be able to accept an incoming connection on the newly added port. Known Problems SW/100-TCP-NCS/AT Version 3.0 has the following known problems: When using the IEN116 Name Server, the command SHow () VERSion does not function correctly if is defined on a secondary name server but not on a primary name server. If, when entering a macro, you press the Break key before the macro input has been fully entered, the portion of the macro that has been entered is executed. Consequently, an error message is usually displayed. To prevent this, after you press the Break key while typing a macro, press the Return key twice before entering the next command. Documentation The following manuals are shipped with SW/100-TCP-NCS/AT Version 3.0: TCP/IP Connection Service User's Guide (3/89) (Part Number: 09-0173-00) Network Management Guide (9/87) (Part Number: 09-0067-02) Getting Started Guide (2/87) (Part Number: 09-0043-01) Configuration Guide (2/88) (Part Number: 09-0093-01) TCP/IP Connection Service Quick Reference Guide (Part Number: 09-0165-00) Refer to the following manuals for more information on SW/100TCP- NCS/AT Version 3.0: Series/100 Installation Guide (10/85) (Part Number: 09-0023-02) NCS/AT Installation and Operation Guide (12/87) (Part Number: 09-0092-02) LAN Planning Guide (2/88) (Part Number: 09-0085-01) If you have any questions, contact your network supplier or 3Com for help. Trademarks UNIX is a registered trademark of AT&T Bell Laboratories.